Skip to content
Omnikalc

Iribarren number calculator: what kind of breaking wave do you get on your beach?

Enter the beach slope, the wave height and the period to get the Iribarren number, the breaker type, the breaking depth and the width of the surf zone.

Updated on
Your inputs
%

Value out of range

ft

Value out of range

s

Value out of range

Results

Iribarren number (surf similarity parameter)

0.84

Plunging breakers: the crest curls and falls, the classic surfing wave
Deep-water wavelength
327.7 ft
Wave steepness H / L₀
0.0092
Estimated depth at breaking
3.8 ft
Estimated width of the surf zone
48 ft

Waves do not all break the same way: some crumble into foam, some curl and crash, some barely break at all. The Iribarren number calculator takes the beach slope, the wave height and the wave period, and gives the Iribarren number with the type of breaker (spilling, plunging or surging), the deep-water wavelength, the wave steepness, the depth at breaking and the width of the surf zone.

How the calculation works

  • Enter the slope of the beach (the rise for 100 units of run, as a percentage), the wave height offshore and the wave period.
  • The calculator finds the deep-water wavelength L₀ = g T² / 2π and the steepness H / L₀ of the waves.
  • It computes the Iribarren number, ξ = tan β / √(H / L₀), which compares the slope of the beach with the steepness of the waves.
  • The value tells the type of breaker: below 0.5 the waves spill, from 0.5 to 3.3 they plunge, and above 3.3 they surge or collapse. It also estimates the depth at breaking and the width of the surf zone.

Example

A swell of 3 ft (0.914 m) with a period of 8 s reaches a beach with a slope of 8 %. The deep-water wavelength is 9.81 × 8² / 2π = 327.7 ft, so the steepness is 0.0092. The Iribarren number is 0.08 / √0.0092 = 0.84, so the waves plunge, as for surfing. They break at a depth of about 3.8 ft, in a surf zone about 48 ft wide.

Why it matters

The way waves break decides how much energy they release on a beach, how far they run up, how they move sand and whether they are good to surf. Coastal engineers use the Iribarren number to design sea walls and breakwaters, since the wave run-up and forces depend on it, and surfers use it to understand why a spot works at some swell sizes and periods and not at others.

Good to know

The number is for waves on a smooth, straight and uniform slope, with an estimate of the height and the period offshore. Real beaches have bars, reefs, rips and varying slopes, and the local slope in the surf zone matters more than the average. The breaking depth uses the rule of thumb of a ratio of 0.78 between wave height and depth, and the surf zone width is only a rough guide.

The ocean wave speed calculator gives the length and speed of waves, the wave power calculator gives the energy they carry, the surfboard volume calculator helps to pick a board, and the tide height calculator gives the water level through the tide.

Frequently asked questions

What is the Iribarren number?

It is a dimensionless number that compares the slope of the beach with the steepness of the incoming waves, also called the surf similarity parameter. It was proposed by the Spanish engineer Ramón Iribarren and used by Battjes (1974) to classify breaking waves. It is the key number for the way a wave breaks, and for how far it runs up the beach.

What are the types of breaker?

Spilling breakers, for ξ below about 0.5, have a crest that crumbles into foam down the face of the wave, on gentle slopes and with steep waves. Plunging breakers, for ξ between 0.5 and 3.3, curl over and crash in front of the wave, with a tube. Surging and collapsing breakers, above 3.3, come on steep beaches with long, low waves, and surge up the beach.

What makes a good surfing wave?

Surfers like plunging or slightly spilling waves that break gradually along the crest, which happens when ξ is between about 0.4 and 2 on a regular slope such as a reef or a sandbar. A steeper bottom gives a hollow, fast wave that is hard to ride, and a very gentle slope gives a slow, mushy wave. The calculator shows which side of the line you are on.

How do the period and the height change the result?

A longer period makes longer, flatter waves with a smaller steepness, which raises ξ and moves the breaker from spilling to plunging, so long-period swell gives better waves than short wind chop. A taller wave of the same period is steeper, which lowers ξ. This is why the same beach has different breakers in different seas.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.