Skip to content
Omnikalc

Optical fiber link budget calculator: check that a link has enough power at the receiver

Enter the transmitter power, the receiver sensitivity, the fiber length and attenuation and the losses of connectors and splices to get the total loss, the received power, the link margin and the maximum reach.

Updated on
Your inputs
dBm

Value out of range

dBm

Value out of range

km

Value out of range

dB/km

Value out of range

Value out of range

dB

Value out of range

Value out of range

dB

Value out of range

dB

Value out of range

Results

Link margin

11.3 dB

Total loss of the link
5.7 dB
Power at the receiver
-8.7 dBm
Margin above the design margin
8.3 dB
The link meets the design margin
Maximum reach with the design margin
33.7 km

Will the light reach the other end? The optical link budget adds the losses of the fiber, the connectors and the splices, and compares the power at the receiver with its sensitivity. The optical link budget calculator gives the total loss, the link margin and the maximum reach that still leaves a design margin.

How the calculation works

  • Enter the transmitter power and the receiver sensitivity from the datasheets of the optics, in dBm.
  • Enter the length and the attenuation of the fiber (about 0.35 dB/km at 1310 nm and 0.22 dB/km at 1550 nm for single-mode, 3 dB/km at 850 nm for multimode).
  • Enter the number of connectors and splices with the loss of each (0.3 to 0.75 dB per connector pair, 0.05 to 0.1 dB per splice) and the design margin you want.
  • The calculator adds all the losses, gives the power at the receiver, the link margin and the maximum reach that still leaves your design margin.

Example

A single-mode link has a transmitter of −3 dBm, a receiver sensitivity of −20 dBm, 10 km of fiber at 0.35 dB/km, 4 connector pairs at 0.5 dB and 2 splices at 0.1 dB. The total loss is 3.5 + 2.0 + 0.2 = 5.7 dB, the received power is −8.7 dBm, and the link margin is 11.3 dB. After a design margin of 3 dB, 8.3 dB remain, and the link could reach 33.7 km.

Why it matters

The calculator helps network engineers, installers, students and ISPs to check a fiber link before the installation, to choose the optics (SFP) for a distance, and to find the weak point of a link that gives errors.

Good to know

The budget is a power budget at one wavelength, and does not include dispersion, reflections, nonlinear effects or the optical amplifiers of long-haul links. Real losses depend on the quality of the work and of the connectors, and they must be checked with a power meter or an OTDR after the installation. Use the maximum specified losses for a conservative design.

The free-space path loss calculator does the same for a radio link, the insertion loss calculator covers a component, the numerical aperture calculator covers the light acceptance of a fiber, and the noise figure calculator covers the noise of an amplifier.

Frequently asked questions

What is a link budget?

A link budget is the accounting of all the gains and losses between a transmitter and a receiver. For an optical fiber link, the power at the receiver is the transmitter power minus the loss of the fiber, the connectors and the splices. This power must be higher than the sensitivity of the receiver, with a margin for aging, repairs and temperature. Everything is added in decibels, which turns the products of losses into sums.

What loss values should I use?

Typical values for single-mode fiber are 0.35 dB/km at 1310 nm and 0.22 dB/km at 1550 nm, and for multimode OM3 or OM4, 3.0 dB/km at 850 nm. A connector pair loses 0.3 dB for a good connection, and standards often allow 0.75 dB. A fusion splice loses about 0.05 to 0.1 dB. For a conservative budget, use the maximum values of the standards (for instance TIA-568) and not the typical ones.

What margin should I keep?

A design margin of 3 dB is common, 1 to 3 dB for short links and more for the links that can be repaired often (each repair adds splices). It covers the aging of the transmitter, the dirt on the connectors, the bends of the cable and the changes of temperature. On the other side, a received power that is too high can overload a receiver: check the maximum input power, and add an attenuator for a short link with a strong laser.

What about dispersion and other limits?

The loss is only one of the limits. At high bit rates and over long distances, the dispersion of the fiber also limits the reach, and the optics have a dispersion penalty. The datasheet of a transceiver gives the maximum reach and the power budget for both. The calculator checks the power budget only, and so the reach is an upper bound.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.