Skip to content
Omnikalc

Vibration isolation calculator: how much of a machine's vibration reaches the floor?

Enter the weight, the stiffness of the mounts, the speed and the damping to get the transmissibility, the natural frequency and the static deflection.

Updated on
Your inputs
lb

Value out of range

lbf/in

Value out of range

rpm

Value out of range

Value out of range

Results

Transmissibility

0.013

Good isolation
Natural frequency of the machine on its mounts
2.80 Hz
Frequency ratio (forcing / natural)
10.73
Vibration isolated
98.7 %
Static deflection of the mounts
1.25 in

A running motor, pump or compressor shakes whatever it sits on, and soft mounts can stop most of the force from reaching the floor, but only if they are chosen well. The vibration isolation calculator takes the weight of the machine, the stiffness of the mounts, the forcing speed and the damping ratio, and gives the transmissibility, the natural frequency, the frequency ratio, the share of vibration isolated and the static deflection.

How the calculation works

  • Enter the weight of the machine, the total stiffness of its mounts and the forcing speed, such as the rotation speed of an unbalanced motor.
  • Enter the damping ratio of the mounts, about 0.02 to 0.05 for steel springs and 0.05 to 0.15 for rubber.
  • The natural frequency is fn = (1/2π) √(k g / W) and the frequency ratio is r = f / fn.
  • The transmissibility is T = √((1 + (2ζr)²) / ((1 − r²)² + (2ζr)²)). Isolation only starts above r = √2 = 1.414.

Example

A machine of 500 lb sits on mounts with a total stiffness of 400 lbf/in, so the natural frequency is 2.80 Hz and the static deflection is 1.25 in. It runs at 1,800 rpm, which is 30 Hz, so the frequency ratio is 10.7. With ζ = 0.05, the transmissibility is 0.0129, so the mounts remove 98.7 % of the vibration force.

Why it matters

Good isolation reduces noise, protects the building and keeps delicate equipment steady. The calculation shows why soft mounts work, why mounts that are too stiff can make things worse by amplifying a vibration near resonance, and how the ratio between the forcing and natural frequencies sets the result.

Good to know

The model has a single degree of freedom with viscous damping, a rigid machine and a rigid floor, and a force at one frequency. Real machines have several frequencies, rocking modes, flexible foundations and non-linear mounts. The stiffness is the total vertical stiffness of all mounts. Use the result for a first selection, and use the mount maker’s data for the design.

The damping ratio calculator describes damped oscillations, the spring-mass calculator finds the natural frequency of an oscillator, the flywheel energy calculator covers rotating masses, and the compression spring calculator sizes springs.

Frequently asked questions

What is transmissibility?

It is the ratio of the force that passes through the mounts into the floor to the force that the machine produces. A value of 1 means that the mounts do nothing, a value above 1 means that they amplify the vibration, and a value of 0.1 means that 90 % of the force is isolated. The same ratio applies to motion isolation of a delicate instrument.

Why must the ratio be above the square root of 2?

Below that ratio, a spring-mass system amplifies the disturbance, and at the natural frequency, resonance makes it large. Isolation begins only when the forcing frequency is more than 1.414 times the natural frequency. In practice, designers aim for a ratio of 3 to 5 or more, which means soft mounts with a large static deflection.

What does damping do?

Damping limits the resonance peak when the machine passes through the natural frequency on start-up and shut-down, but it raises the transmissibility above the resonance. This is why very soft, lightly damped steel springs isolate best at high frequencies, while rubber mounts, which damp more, are a compromise.

How is the static deflection related?

The natural frequency of a mass on a spring follows from its static deflection: fn ≈ 15.8 / √(deflection in mm), or 3.13 / √(deflection in inches). A larger deflection means a lower frequency and better isolation. The calculator gives the deflection under the weight, which also tells you how much the machine sinks when the mounts are loaded.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.