Skip to content
Omnikalc

Beam camber calculator: how much camber to give a steel beam for its dead load?

Enter the span, the dead and live loads, the moment of inertia and the share of the dead load deflection to camber to get the dead load deflection, the camber, the rounded camber and the live load deflection check.

Updated on
Your inputs
ft

Value out of range

lb/ft

Value out of range

lb/ft

Value out of range

in⁴

Value out of range

%

Value out of range

Results

Camber rounded to 1/4 in

1.25 in

Dead load deflection
1.61 in
Camber to give the dead load deflection share
1.29 in
Live load deflection
1.07 in
Live load deflection over L/360
0.81
The live load deflection is within L/360

The beam camber calculator gives the camber of a simply supported steel beam from its dead load deflection, with the share to compensate, the camber rounded to 1/4 in for the fabricator and the check of the live load deflection against the limit L/360.

How the calculation works

  • Enter the span of the simply supported steel beam and its moment of inertia Ix.
  • Enter the dead load (self-weight, slab, finishes) and the live load, in pounds per foot.
  • Enter the share of the dead load deflection that is cambered, usually 70 to 80% for the steel beams.
  • The calculator finds the dead load deflection, the camber, the camber rounded to the nearest 1/4 in for the fabricator and the live load deflection compared with the limit L/360.

Example

A steel beam of 40 ft with Ix = 1,480 in⁴ carries 1,200 lb/ft of dead load. The dead load deflection is 5 w L⁴ / (384 E I) = 1.61 in. A camber of 80% is 1.61 × 0.8 = 1.29 in, which the fabricator rounds to 1.25 in. The live load of 800 lb/ft gives 1.07 in of deflection, against the limit L/360 = 1.33 in, which is a ratio of 0.81.

Why it matters

The calculator helps structural engineers, steel detailers, fabricators and students to specify the camber of a beam on the drawings, to see whether the camber is worth it and to check the stiffness under the live load. It reproduces the usual hand calculation of the deflection.

Good to know

Specify camber only for deflections that are large enough to see, and give the loads on the drawings so that the fabricator can check. Do not camber a beam that is part of a composite system without checking the construction stages. Check the deflection of the beam before and after the concrete has set, and the ponding of a flat roof.

The beam deflection calculator covers other support and load cases, the steel beam LTB capacity calculator checks the flexural strength, the two-span continuous beam calculator covers continuous beams and the wood beam span calculator checks the beams of wood.

Frequently asked questions

What is camber?

Camber is a curvature given to a beam in the shop, opposite to the deflection that the loads will cause, so that the beam is level when the dead load is in place. It is common in the steel and in the prestressed concrete beams for long spans, and it improves the appearance and the drainage of a floor or a roof. The camber is specified on the drawings and made by the fabricator, by bending the beam cold or by heat.

How is the camber chosen?

The camber is a share of the deflection under the dead load, usually 70 to 80% for the steel beams, because the live load and the part of the dead load applied later are not known with certainty. AISC suggests camber only when the deflection is over about 3/4 in, and the camber is given to the nearest 1/4 in because the process of the mill does not allow a better accuracy. The deflection for the camber is computed with the loads applied on the bare steel beam.

What is the live load limit?

The deflection under the live load is limited by the building code to avoid damage to the finishes and an annoying vibration, usually to L/360 for a floor with plaster, and L/240 for a roof. Camber does not help for the live load deflection, which has to be controlled by the stiffness of the beam, its moment of inertia. For this reason the calculator checks the live load deflection separately.

What are the limits of the calculator?

The calculator uses the formula of a simply supported beam under a uniform load, for a steel with E = 29,000 ksi. A composite beam, a continuous beam, point loads, loads applied at different stages and the effect of the creep need a more detailed analysis. The shipping and the erection can also change the camber. The beam and its camber must be specified by a structural engineer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.