Skip to content
Omnikalc

Prying action calculator: flange thickness of a tee-stub with bolts in tension

Enter the flange thickness, the bolt tension, the geometry of the tee-stub and the steel strength to get β, the prying factor α', the required flange thickness and the ratio to the thickness provided.

Updated on
Your inputs
in

Value out of range

kips

Value out of range

kips

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

ksi

Value out of range

Results

Thickness required to thickness provided

0.98

The flange is thick enough, with the prying action included
Parameter β
0.141
Prying factor α'
0.207
Required flange thickness
0.738 in

The prying action calculator gives the parameters β and α’, the required flange thickness and the ratio to the thickness provided of a bolted tee-stub or end plate connection in tension, by the procedure of the AISC Steel Construction Manual.

How the calculation works

  • Enter the thickness of the flange, the required tension and the available tension strength of one bolt.
  • Enter the distance b from the bolt line to the web face, the distance a to the edge of the flange, the tributary length per bolt and the bolt diameter.
  • Enter the tensile strength of the flange. The calculator finds β and the prying factor α’, the required flange thickness by the AISC procedure and the ratio to the thickness provided.

Example

A tee-stub flange of 0.75 in has bolts of 3/4 in with a required tension of 27 kips and an available strength of 29.8 kips, with b = 1.75 in, a = 1.5 in, a pitch of 4 in and Fu = 65 ksi. Then b’ = 1.375 in, a’ = 1.875 in, ρ = 0.733, δ = 1 − 0.8125 / 4 = 0.797, β = (29.8 / 27 − 1) / 0.733 = 0.141 and α’ = 0.207. The required thickness is √(4.44 × 27 × 1.375 / (4 × 65 × (1 + 0.797 × 0.207))) = 0.738 in, a ratio of 0.98.

Why it matters

The calculator helps steel designers, detailers and students to size the thickness of hanger connections, tee-stub connections and end plates in a first design, and to see how the bolt position, the pitch and the steel strength change the flange thickness needed.

Good to know

Keep the bolt line as close as possible to the web, within the clearance for the wrench, and use a thicker flange if the ratio is close to 1. Check also the bolts for the tension with the prying force, the flange in shear and the weld to the web.

The bolt shear capacity calculator checks the bolts in shear, the bolt joint stiffness calculator shows the effect of the stiffness on the load in the bolts, the steel tension member calculator checks a plate in tension and the Whitmore width calculator checks a gusset plate.

Frequently asked questions

What is prying action?

Prying action is the extra tension in the bolts of a connection loaded in tension, such as a tee-stub, a hanger or an end plate, caused by the bending of a flexible flange. When the flange bends, its edges push against each other and create a prying force Q at the tips of the flange, which adds to the load in the bolts. A thicker flange is stiffer and reduces the prying action.

How is the required thickness found?

The AISC Manual procedure uses the distances b' = b − d/2 and a' = a + d/2 to the bolt, the ratio ρ = b'/a', the factor δ = 1 − d'/p for the bolt holes and the parameter β = (1/ρ)(B/T − 1), where B is the available strength and T the required tension of the bolt. The prying factor is α' = 1 if β ≥ 1, otherwise α' = β / (δ (1 − β)) but not more than 1. The required thickness is t = √(4.44 T b' / (p Fu (1 + δ α'))).

What does the prying factor α' mean?

A value α' = 0 means that the flange is thick enough to have no prying action, and α' = 1 means that the flange is thin and that it has a full prying action. The bolts and the flange are then checked for the tension plus the prying force. In practice, a thicker flange, a bolt line close to the web or more bolts is a way to reduce the prying action and the load on the bolts.

What are the limits of the calculator?

The calculator gives the flange thickness for a single bolt line on each side of the web, with the a ≤ 1.25 b limit. It does not include the yielding line mechanisms of the end plates with several bolt rows, the shear and the tension interaction in the bolts, the fatigue and the weld of the tee to the web. The design of the connection must follow the specification and be made by a qualified engineer.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.