Skip to content
Omnikalc

Bridge pier scour calculator: depth of the scour hole at a bridge pier

Enter the flow depth and velocity, the pier width and length, the angle of attack and the shape and bed factors to get the Froude number, the scour depth from the CSU equation and the design scour depth.

Updated on
Your inputs
ft

Value out of range

ft/s

Value out of range

ft

Value out of range

ft

Value out of range

°

Value out of range

Results

Design scour depth

8.57 ft

Froude number of the approach flow
0.446
Angle of attack factor K2
1.00
Scour depth from the CSU equation
8.57 ft
Upper limit of the scour depth (HEC-18)
9.60 ft

The bridge pier scour calculator gives the local scour depth around a bridge pier from the flow depth, the velocity, the pier width and shape and the angle of attack, with the CSU equation of the FHWA manual HEC-18 and its upper limit.

How the calculation works

  • Enter the flow depth and the velocity just upstream of the pier, and the pier width and length.
  • Enter the angle of attack of the flow on the pier, which is 0° when the pier is aligned with the flow.
  • Choose the nose shape factor K1 and the bed condition factor K3 for the river.
  • The calculator applies the CSU equation ys = 2 K1 K2 K3 y1 (a / y1)^0.65 Fr^0.43 and the limit of 2.4 a (or 3.0 a for Fr above 0.8).

Example

A round-nosed pier 4 ft wide and 20 ft long sits in a flow 10 ft deep at 8 ft/s, aligned with the flow, on a plane bed. The Froude number is 8 / √(32.2 × 10) = 0.446, K1 = 1.0, K2 = 1.00 and K3 = 1.1. The scour depth is 2 × 1.0 × 1.0 × 1.1 × 10 × (4 / 10)^0.65 × 0.446^0.43 = 8.57 ft, below the limit of 2.4 × 4 = 9.60 ft, so the design scour depth is 8.57 ft.

Why it matters

The calculator helps bridge and hydraulic engineers, inspectors and students to estimate how deep a pier foundation must go or how much riprap protection is needed, and to see the effect of the shape and of the alignment of a pier. It gives a first estimate before a full hydraulic and scour analysis.

Good to know

Use the design flood and the check flood of your authority, and the velocity and depth upstream of the pier, not the average of the section. Add the long-term degradation and the contraction scour. Remember that the scour hole fills again after the flood, so it can be invisible at an inspection. A scour countermeasure and a monitoring plan may be needed, and the design must be made by a qualified engineer.

The weir flow calculator and the broad-crested weir calculator cover flow over structures, the riprap sizing calculator gives the size of protection stones and the Manning equation calculator gives the flow velocity of a channel.

Frequently asked questions

What is bridge pier scour?

Scour is the removal of the bed material by the flow around a pier. The flow hits the upstream face, goes down along it and forms a horseshoe vortex at the base that digs a hole. Scour is the main cause of bridge failures in the United States, so the foundation of a pier in a river must be placed below the depth of the deepest scour expected during a flood.

What is the CSU equation?

The Colorado State University equation, recommended in the FHWA manual HEC-18, gives the maximum local scour depth at a pier for a live bed or clear water: ys / y1 = 2 K1 K2 K3 (a / y1)^0.65 Fr1^0.43. It uses the flow depth y1, the pier width a and the Froude number Fr1 of the approach flow, with factors for the nose shape, the angle of attack and the bed forms.

How does the angle of attack change the scour?

When the flow is not aligned with the pier, the projected width increases and the scour hole is deeper. The factor K2 = (cos θ + (L / a) sin θ)^0.65 rises quickly with the angle and with the ratio of length to width of the pier. The HEC-18 manual limits K2 to 2.5 for L / a above 12, and recommends circular piers or piers aligned to the flood flow where the direction can change.

What are the other components of scour?

The local scour at a pier is added to the long-term degradation of the river bed and to the contraction scour caused by the narrowing of the channel by the bridge. A full scour analysis also includes the scour at the abutments. The result of the CSU equation is for a single pier in a sand bed, and for a cohesive soil, a rock or a coarse bed, other methods and a site study are needed.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.