Skip to content
Omnikalc

Check dam spacing calculator: number of dams and tons of stone for a ditch

Enter the channel slope, the dam height and the channel length, and the dam shape and stone density to get the spacing, the number of dams, the stone per dam, the total stone and the tons.

Updated on
Your inputs
%

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

Value out of range

ft

Value out of range

tons/yd³

Value out of range

Results

Weight of the stone

44.8 tons

Spacing between the dams
37.5 ft
Number of dams
18
Stone per dam
1.78 yd³
Stone for all the dams
32.0 yd³

The check dam spacing calculator gives the spacing between the dams, their number, the stone per dam, the total stone and its weight to control the erosion of a drainage ditch or swale, from the slope of the channel, the height of the dams and the length to protect.

How the calculation works

  • Enter the slope of the channel, the effective height of the dam and the length of channel to protect.
  • Enter the top width, the side slopes, the length across the channel of the dam and the stone density.
  • The calculator finds the spacing of the dams, their number, the stone per dam, the total stone and its weight.

Example

A channel with a slope of 4 % is protected with check dams 1.5 ft high. The crest of one dam is at the level of the toe of the next, so the spacing is 1.5 / 0.04 = 37.5 ft. A channel of 650 ft needs ceil(650 / 37.5) = 18 dams. With a top width of 1 ft and side slopes of 2:1, the base is 7 ft and the section is 6 ft². For a dam 8 ft long, the stone is 6 × 8 / 27 = 1.78 yd³, or 32.0 yd³ for all the dams and 44.8 tons at 1.4 tons/yd³.

Why it matters

The calculator helps erosion control designers, site managers, contractors and students to plan a series of check dams in a ditch, to see how the slope and the height change the number of dams, and to order the right tonnage of stone for the job.

Good to know

Make the center of each dam lower than the sides, so that the water goes over the center and not around the dam. Use a clean, angular stone of 2 to 9 in, or 50 to 225 mm, and key the dam into the bank. Inspect the dams after each rain, remove the sediment before it reaches half the height of the dam, and replace the stone that is washed away.

The channel lining tractive force calculator checks the lining of a channel, the riprap calculator gives the stone for the protection of a slope, the silt fence posts and fabric quantity calculator estimates a sediment barrier and the Manning equation calculator gives the flow of a channel.

Frequently asked questions

What is a check dam?

A check dam is a small dam of stone, gravel bags, logs or another material that is built across a drainage ditch or a swale. It slows the water, reduces the erosion of the bottom of the ditch and lets the sediment settle behind it. It is a temporary erosion control used on a construction site until the ditch has a permanent lining or a vegetation.

How is the spacing found?

The usual rule is to space the dams so that the crest of one dam is at the same level as the toe of the dam upstream. The spacing is then the effective height of the dam divided by the slope of the channel, in decimal form. On a steep channel, the dams are close, and on a flat channel they are far apart. The calculator uses this rule and rounds up the number of dams.

How is the stone quantity found?

The section of a dam is a trapezoid, with the top width, the side slopes and the height. The base of the trapezoid is the top width plus twice the side slope times the height. The section times the length of the dam across the channel gives the volume of stone of one dam, and the weight is this volume times the density of the stone, which depends on the rock and on the voids.

What are the limits of the calculator?

The calculator gives the quantities of stone for a series of identical dams. It does not check the capacity of the channel, which needs the notch in the center of the dam to carry the flow, nor the velocity of the water, the size of the stone against the flow or the stability of the dam. The dams are not suitable in a live stream, and the sediment must be removed when it reaches half the height.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.