Skip to content
Omnikalc

Column effective length factor K calculator

Enter the column and the beams at each joint to get the ratios G, the effective length factor K for a braced or unbraced frame and the slenderness KL/r.

Updated on
Your inputs
in⁴

Value out of range

ft

Value out of range

in

Value out of range

in⁴

Value out of range

ft

Value out of range

Value out of range

in⁴

Value out of range

ft

Value out of range

Value out of range

Results

Effective length factor K

1.62

G at the top joint
1.59
G at the bottom joint
2.54
Effective length KL
22.7 ft
Slenderness KL/r
44.3
A moderate slenderness

The column effective length factor calculator gives the stiffness ratios G at the two joints, the effective length factor K of the alignment chart for a braced or unbraced frame, the effective length KL and the slenderness KL/r.

How the calculation works

  • Enter the moment of inertia, the height and the radius of gyration of the column.
  • Enter the beams that frame into the top joint and into the bottom joint, or choose a fixed or pinned base, and choose braced or unbraced.
  • The calculator finds the stiffness ratios G, the effective length factor K, the effective length and the slenderness.

Example

A W14×90 column (I = 999 in⁴, r = 6.14 in) 14 ft high is framed at the top to two beams of 1,350 in⁴ and 30 ft and at the bottom to two beams of 843 in⁴ and 30 ft. The stiffness ratios are G = 1.59 at the top and 2.54 at the bottom. In an unbraced frame K = 1.62, so KL = 1.62 × 14 = 22.7 ft and KL/r = 44.3. In a braced frame the same column has K = 0.86 only.

Why it matters

The calculator helps structural engineers, steel designers and students to get the K factor of a frame column without reading the nomograph, to compare a braced with an unbraced frame, and to see how the stiffness of the beams or the fixity of the base changes the buckling length.

Good to know

Use the stiffness of the beams with the correct end condition: for a beam far end pinned, multiply its stiffness by 1.5 in a braced frame, and by 0.5 in an unbraced one. Use the gross moment of inertia for an elastic check and keep K at least 1.0 for an unbraced frame. For a pinned base the AISC commentary allows a G of 10, and for a base with a real footing a G between 1 and 5 is common, so a G of 1 is only for a base really fixed.

The steel column capacity calculator gives the AISC strength from KL/r, the Euler buckling calculator gives the elastic critical load, the base plate size calculator sizes the plate under the column and the wood column capacity calculator does the same check for a post.

Frequently asked questions

What is the effective length factor K?

K is the factor that turns the real height of a column into the length of an equivalent pinned column, so that the Euler buckling load works. K is 1.0 for pinned ends that cannot sway, 0.5 for two fixed ends, 2.0 for a flagpole and above 1.0 for most columns of an unbraced frame. The effective length KL is used in the slenderness KL/r and in the column strength.

What is the ratio G?

At a joint, G is the sum of the stiffness EI/L of the columns divided by the sum of the stiffness EI/L of the beams. A stiff beam gives a small G, close to 1.0 for a joint that is nearly fixed. A flexible beam gives a large G, with 10 used for a pinned base in practice. The two values GA and GB at the ends of the column give K on the alignment chart, which the calculator replaces by a fitted equation.

Which equation does the calculator use?

The calculator uses the Dumonteil fits of the alignment chart, which are within a few percent of the chart. The braced equation is K = (3 GA GB + 1.4 (GA + GB) + 0.64) / (3 GA GB + 2.0 (GA + GB) + 1.28). The unbraced equation is K = √((1.6 GA GB + 4 (GA + GB) + 7.5) / (GA + GB + 7.5)). Both assume elastic behavior, equal columns above and below the joint and beams bent in single or double curvature.

When is the chart not valid?

The chart assumes an elastic column, a rigid joint and no axial force in the beams, and its base is a story of a regular frame. In an inelastic column the stiffness is reduced and K is lower. In a frame with leaning columns, different story heights, partially restrained joints or a high axial load use the AISC direct analysis method with notional loads, and take K as 1.0 in that method.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.