Skip to content
Omnikalc

Grade stake cut and fill calculator: level readings and grade rod

Enter the benchmark elevation, the backsight, the foresight and the design grade to get the height of the instrument, the ground elevation, the cut or fill and the grade rod.

Updated on
Your inputs
ft

Value out of range

ft

Value out of range

ft

Value out of range

ft

Value out of range

Results

Cut (+) or fill (−)

0.37 ft

Cut: the ground is higher than the design grade
Height of the instrument
104.52 ft
Ground elevation at the stake
98.37 ft
Cut or fill in inches
4.4 in
Rod reading to be at grade
6.52 ft

The grade stake cut and fill calculator gives the height of the instrument, the ground elevation, the cut or fill and the grade rod reading from a level setup, the benchmark elevation, the rod readings and the design finish grade.

How the calculation works

  • Enter the elevation of the benchmark and the rod reading taken on it (backsight).
  • Enter the rod reading on the ground at the stake (foresight) and the design finish grade at the stake.
  • The calculator finds the height of the instrument, the ground elevation, the cut or fill and the rod reading that gives the design grade.

Example

A benchmark at 100.00 ft is read at 4.52 ft on the rod, so the height of the instrument is 104.52 ft. A reading of 6.15 ft on the ground at the stake gives a ground elevation of 104.52 − 6.15 = 98.37 ft. For a design grade of 98.00 ft, the cut is 98.37 − 98.00 = 0.37 ft, or 4.4 in, and the rod reads 104.52 − 98.00 = 6.52 ft when the stake is at grade.

Why it matters

The calculator helps surveyors, foremen, equipment operators and students to set the grade stakes of an earthwork job, to find the cut or the fill at a point from a reading, and to find the rod reading that gives the finish grade, without the need to redo the arithmetic after each reading.

Good to know

Set the level on firm ground, level the instrument carefully and keep the sights short and balanced. Read the rod held plumb with a rod level, and close the level run on the benchmark. Write the cut or the fill on the stake with the sign, and check the elevation of the benchmark with a second one before the work.

The average end area volume calculator turns the cuts and fills of the sections into a volume, the earthwork swell and shrink calculator gives the volume to haul, the motor grader blading production calculator plans the finish grading and the dozer production blade calculator sizes the earthmoving.

Frequently asked questions

What is the height of the instrument?

With an optical level, the height of the instrument is the elevation of the line of sight. It is the elevation of the benchmark plus the rod reading on the benchmark, called the backsight. Every reading taken with the same setup is then subtracted from the height of the instrument to give the elevation of the point where the rod stands. The method is the same for an optical, a laser or a digital level.

How are the cut and the fill found?

The ground elevation at the stake is the height of the instrument minus the foresight on the ground. The difference between the ground elevation and the design finish grade is the cut, if the ground is higher than the grade, or the fill, if the ground is lower. In the calculator, a positive value is a cut and a negative value is a fill, as it is usual in the earthwork plans and on the grade stakes.

What is the grade rod?

The grade rod is the reading on the rod that corresponds to the design grade, that is the height of the instrument minus the design elevation. When the rod is held on a point and reads this value, the point is exactly at the design grade. It is used to set the grade stakes, to check the subgrade and to control the machines that are cutting or filling to the grade.

What are the limits of the calculator?

The calculator makes the arithmetic of one setup of the level. It does not correct for the curvature of the Earth and the refraction on long sights, the error of the collimation of the level, the settlement of the tripod, or the error of the plumb of the rod. Long sights should be balanced between the backsight and the foresight, and the levels should be closed on a known benchmark to find the closure error.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.