Skip to content
Omnikalc

Kerf bending spacing calculator

Enter the stock thickness, the thickness left uncut, the kerf width, the radius and the angle of the curve to get the kerf spacing, the number of kerfs and the length of the kerfed section.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

°

Value out of range

Results

Spacing between kerfs

2.492 in

Number of kerfs

8

Length of the kerfed section along the face

18.8 in

Angle closed by each kerf
11.31 °
Depth of each kerf
0.625 in
Radius at the web
12.63 in
Web radius to web thickness
101

The kerf bending spacing calculator gives the spacing between kerfs, the number of kerfs and the length of the kerfed section needed to bend a board to a chosen radius and angle, from the thickness, the web left uncut and the kerf width.

How the calculation works

  • Enter the stock thickness, the web left uncut and the kerf width.
  • Enter the radius of the concave face and the angle of the curve.
  • Read the spacing, the number of kerfs and the length of the bend.

Example

A board 0.75 in thick with a web of 0.125 in has kerfs 0.625 in deep. A kerf of 0.125 in closes 11.31 °. To bend it to a radius of 12 in over 90 °, space the kerfs 2.492 in apart and cut 8 of them, over a section 18.8 in long. The radius at the web is 12.63 in, which is 101 times the web thickness.

Why it matters

The calculator helps woodworkers who build curved cabinet doors, speaker enclosures, arched frames, guitar sides and wall panels from flat boards and who need to know where to cut so the curve is smooth and the kerfs close completely.

Good to know

Cut all the kerfs to the same depth with a stop or a jig, on a table saw or a router table, and keep the web even because it sets the thickness and strength. Test the spacing on a scrap and adjust, since the real kerf closes a little less than the geometry, and the saw blade kerf can differ from the nominal width. Keep the kerfs parallel to the axis of the curve. Check the ratio of the radius to the web so that the web does not crack, and bend slowly, with the wood at a normal moisture content.

The resaw and bookmatch calculator splits thick boards, the bend allowance calculator treats metal, the box joint calculator lays out fingers and the board cut list calculator plans the cuts.

Frequently asked questions

How does kerf bending work?

A series of parallel saw cuts, the kerfs, are made across the back of a board, leaving a thin web on the front. When the board is bent toward the kerfed side, each kerf closes and turns the board by a small angle. A board with many kerfs follows a curve whose radius depends on the kerf width, the depth and the spacing.

What is the spacing formula?

Each kerf closes by an angle α = arctan(k / h), where k is the kerf width and h the depth of the cut. The spacing along the curve is the radius at the web times that angle: s = (R + h) × α, where R is the radius of the concave face. A smaller radius needs closer kerfs.

How thick must the web be?

The web must be thin enough to bend without breaking and thick enough to hold the shape. A web of about 1/8 inch, or 3 millimeters, is common on wood. The ratio of the web radius to the web thickness should stay above about 30 to 50. A tighter radius needs a thinner web or steaming.

How should the bend be finished?

The kerfs are usually glued shut, filled with glue and a filler of sawdust or thin wood, or covered with a veneer or a skin of plywood. Clamp the bent piece to a form until the glue cures. The kerfs can also be left visible as a decorative pattern when the piece is not load-bearing.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.