Skip to content
Omnikalc

Mortise and tenon sizing calculator

Enter the rail thickness and width, the leg thickness, the shoulder allowance and the tenon length to get the tenon dimensions, the mortise size, the wall left in the leg and the cheek glue area.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in

Value out of range

%

Value out of range

in

Value out of range

in

Value out of range

in

Value out of range

Results

Tenon thickness

0.247 in

Tenon width

2.500 in

Mortise depth

1.313 in

Wall left on each side of the mortise
0.751 in
Glue area of the two cheeks
6.25 in²
Tenon cross section
0.619 in²
Tenon width to thickness
10.1

The mortise and tenon sizing calculator gives the tenon thickness, width and length, the mortise depth, the wall left on each side in the leg and the cheek glue area from the dimensions of the rail and of the leg, the shoulder allowance and the thickness ratio.

How the calculation works

  • Enter the rail thickness and width, and the leg thickness.
  • Enter the tenon thickness ratio, the shoulder allowance, the tenon length and the extra mortise depth.
  • Read the tenon, the mortise, the walls and the glue area.

Example

A rail 0.75 in thick and 3 in wide in a leg 1.75 in thick gets a tenon 0.247 in thick and 2.500 in wide, with a length of 1.25 in. The mortise is 1.313 in deep and leaves 0.751 in of wood on each side. The two cheeks give 6.25 in² of glue area, and the tenon section is 0.619 in².

Why it matters

The calculator helps woodworkers who build tables, chairs, doors and frames and who want sound proportions for a mortise and tenon joint. It gives the sizes to mark on the rail and the leg and checks that the wall left in the leg is thick enough.

Good to know

Mark the mortise first and cut the tenon to fit it, not the other way, and test the fit on a scrap. A tenon should go in with hand pressure and without force. Keep the grain of the tenon along the length of the rail for strength. For wide rails, cut two tenons or a haunch. The ratios here are the classic guidelines, and heavy loads, softwoods or thin legs need larger sections and extra checks.

The dovetail joint calculator treats another classic joint, the box joint calculator lays out fingers, the pocket hole calculator handles a quicker joint and the wood beam span calculator checks a loaded member.

Frequently asked questions

How thick should a tenon be?

The classic rule is to make the tenon about one third of the thickness of the rail, and no more than half. A thicker tenon leaves the rail shoulders too thin and gives a weak mortise wall, while a thinner one has less glue area and strength. For a rail of 3/4 inch, a tenon of 1/4 inch is typical.

How long should the tenon be?

A longer tenon gives more glue surface and a stronger joint. A length of 1 to 1.5 inches is common in furniture, and the mortise should be a little deeper, about 1/16 inch, so that the tenon bottoms out on glue and not on the wood. In thick legs, a tenon length of about two thirds of the leg is often used.

What is the shoulder allowance?

The shoulders leave a margin on each side of the tenon width, usually 1/4 inch, so that the tenon does not break through the edge of the leg and the shoulder hides the mortise edges. Wide rails can use a haunch or two tenons to avoid a mortise that is too long.

How much wall must stay in the leg?

The wall between the mortise and the face of the leg should be at least about 1/4 inch, and thicker in hardwoods under load. If the leg is thin, reduce the tenon thickness, or offset the mortise toward the outer face, while keeping enough wood on the inner side to take the load.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.