Skip to content
Omnikalc

Pedestrian bridge vertical frequency and footfall check calculator

Enter the span, the modulus, the inertia and the weight per foot to get the first vertical frequency, the ratio to the 3 Hz limit and the inertia needed.

Updated on
Your inputs
ft

Value out of range

ksi

Value out of range

in⁴

Value out of range

lb/ft

Value out of range

Hz

Value out of range

Results

First vertical frequency

3.33 Hz

Frequency to limit ratio
1.11
The frequency is above the limit with a margin
Moment of inertia needed for the limit
4,374 in⁴
Deflection under the dead load
1.12 in

The pedestrian bridge frequency calculator gives the first vertical natural frequency of a simply supported bridge, its ratio to the frequency limit (3 Hz in the AASHTO guide), the moment of inertia needed for the limit and the dead load deflection.

How the calculation works

  • Enter the span, the modulus of elasticity, the moment of inertia and the weight per foot of the bridge.
  • Enter the frequency limit, 3 Hz for the vertical vibration in the AASHTO guide.
  • The calculator gives the first vertical frequency, the ratio to the limit, the inertia needed and the dead load deflection.

Example

A simply supported bridge of 60 ft with 29,000 ksi steel, an inertia of 5,400 in⁴ and a weight of 600 lb/ft has a mass of 600 / 12 / 386.4 = 0.1294 lb·s²/in². The first frequency is f = π / (2 L²) × √(E I / m) = 3.33 Hz, a ratio of 1.11 to the limit of 3.0 Hz. The inertia needed for exactly 3.0 Hz is 4,374 in⁴. The deflection under the dead load is 1.12 in.

Why it matters

The calculator helps bridge engineers, architects, designers of footbridges and students to check the vertical frequency of a pedestrian bridge at the start of a design, to choose the depth of the girders and to decide if a vibration analysis is needed.

Good to know

Use the weight of the deck, the finishes, the railings and the services, since the mass lowers the frequency, and the composite section stiffness with the modular ratio for a concrete deck. Check the frequency again with the final weights. For a long span, a light deck or a bridge near a gym, a stadium or a railway station, ask for a dynamic analysis even if the frequency is above 3 Hz.

The floor walking vibration calculator checks the peak acceleration of a floor, the tuned mass damper calculator sizes a damper, the beam deflection calculator gives the deflection of a beam and the steel beam lateral-torsional buckling calculator checks the flexural strength.

Frequently asked questions

Why is the frequency checked?

People walk with a step rate of 1.6 to 2.4 steps per second, and their second harmonic reaches 3.2 to 4.8 Hz. A bridge whose first vertical frequency is in these ranges can enter in resonance with the footfalls, and the deck moves in a way that is felt and can be unpleasant. The AASHTO guide specification for pedestrian bridges asks for a first vertical frequency over 3.0 Hz so that the first harmonic is avoided and the second can be checked.

What is the formula?

For a simply supported uniform beam, the first natural frequency is f = π / (2 L²) × √(E I / m), where m is the mass per unit length, equal to the weight per unit length divided by g. The frequency rises with the stiffness EI and falls with the mass and the square of the span. It is also approximately 0.18 √(g / δ), with δ the static deflection under the dead load, so a bridge with a dead load deflection of 1 in has a frequency near 3.5 Hz.

What if the frequency is under 3 Hz?

A bridge under the limit is not rejected, but the guide asks for an analysis of the response to the walking load, with the acceleration compared with a comfort limit, or for a damper such as a tuned mass damper. The lateral frequency should be above 1.3 Hz to avoid the lateral lock-in of a crowd. Raising the stiffness, shortening the span or lightening the deck brings the frequency up.

What does the calculator leave out?

The calculator takes a simple span of constant section and the weight that you give, and it does not include the pedestrians, the continuous spans, the cantilevers, the cables, the damping or the peak acceleration. It gives the vertical frequency only, and the lateral frequency, which depends on the lateral stiffness, is not computed. Use a finite element model for a long, light or cable-supported bridge.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.