Skip to content
Omnikalc

Scraper production calculator: cycle time, loose and bank yards per hour

Enter the bowl capacity, the fill factor, the haul and return distances, the speeds, the fixed time, the swell and the job volume to get the cycle, the trips, the production and the hours.

Updated on
Your inputs
yd³

Value out of range

Value out of range

ft

Value out of range

ft

Value out of range

mph

Value out of range

mph

Value out of range

min

Value out of range

min

Value out of range

%

Value out of range

yd³

Value out of range

Results

Bank volume per hour

144.5 yd³/h

Cycle time
5.98 min
Trips per hour
8.37
Loose volume per hour
180.7 yd³/h
Hours for the job
346 h

The scraper production calculator gives the cycle time, the trips per hour, the loose and bank production and the hours needed for a job of scraper haul, from the capacity of the bowl, the fill factor, the distances and the speeds.

How the calculation works

  • Enter the bowl capacity, the fill factor, the haul and return distances and the speeds loaded and empty.
  • Enter the load, maneuver and dump time, the working minutes per hour, the swell of the soil and the job volume.
  • The calculator finds the cycle time, the trips per hour, the loose and bank production and the hours for the job.

Example

A scraper with a bowl of 24 yd³ and a fill factor of 0.9 hauls 3,000 ft loaded at 15 mph (2.27 min) and returns 3,000 ft empty at 20 mph (1.70 min). With 2.0 min to load, maneuver and dump, the cycle is 5.98 min. In a 50 min hour, that makes 8.37 trips, or 24 × 0.9 × 8.37 = 180.7 yd³/h loose. With 25 % swell, the bank production is 144.5 yd³/h, and a job of 50,000 yd³ takes 346 h.

Why it matters

The calculator helps earthwork contractors, estimators and students to estimate the production of a scraper on a haul, to compare several haul distances or speeds, to find how many hours a scraper needs for a volume, and to choose between a scraper, a loader with trucks and a dozer push.

Good to know

Keep the haul road wide, smooth and well watered, and cut the grade where it is possible, because the speed of the loaded scraper depends on it. Load downhill with a push loader to get a full bowl in a short time. Use the average speeds measured on site if they are known, and add a margin of 10 to 20 % to the hours for the weather and the breakdowns.

The wheel loader cycle production calculator sizes a loader, the excavator productivity cycle calculator sizes an excavator, the haul truck rimpull and grade calculator checks the speed on a grade and the earthwork swell and shrink calculator gives the volumes of the soil.

Frequently asked questions

What is a scraper?

A scraper is an earthmoving machine with a bowl that cuts a thin layer of soil, carries it and spreads it at the fill, all in one unit. It is the most efficient machine for hauls from about 300 to 5,000 ft, or 100 to 1,500 m, when the soil is easy to dig and the haul roads are good. A push loader or a second scraper is often used to help the loading.

How is the cycle time found?

The cycle time is the sum of the fixed time and of the travel times. The fixed time is made of the loading, the maneuvers and the dumping, and it is often between 1.5 and 3 minutes. The travel time is the distance divided by the average speed, loaded for the haul and empty for the return. In imperial units, 1 mph is 88 ft/min, and in metric, 1 km/h is 16.67 m/min.

What is the fill factor?

The fill factor is the part of the heaped capacity of the bowl that is really filled during the loading. It is lower in hard or rocky soils and higher in loose soils or with a push loader. The bowl fill is the heaped capacity times the fill factor, in loose measure. This volume is divided by one plus the swell to get the volume in the bank, which is the measure of the earthwork quantities.

What are the limits of the calculator?

The calculator uses average speeds on a level road. It does not take into account the grades, which change the speeds a lot and can be computed with the rimpull of the machine, the rolling resistance of the road, the number of scrapers per push loader, the spreading and the compaction. The real production also depends on the operator, the weather and the condition of the haul road. Use the result as an estimate and follow the real data of the job.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.