Skip to content
Omnikalc

Timber beam stability factor CL calculator

Enter the unbraced length, the beam size and the design values to get the NDS beam stability factor CL, the reduced bending value and the moment capacity.

Updated on
Your inputs
in

Value out of range

in

Value out of range

in

Value out of range

psi

Value out of range

psi

Value out of range

Results

Beam stability factor CL

0.733

A noticeable loss of strength: add lateral bracing
Effective length Le
176.6 in
Slenderness ratio RB
26.9
Critical buckling design value FbE
958 psi
Reduced bending design value Fb' (before other factors)
843 psi
Moment capacity at Fb'
1.50 kip·ft

The timber beam stability factor calculator gives the NDS beam stability factor CL from the unbraced length, the beam slenderness RB and the critical buckling stress FbE, and the reduced bending value and moment capacity of the beam.

How the calculation works

  • Enter the unbraced length of the compression edge, and the width and depth of the beam.
  • Enter the adjusted bending design value Fb* (all adjustment factors except CL and the volume factor) and the adjusted minimum modulus E’min.
  • The calculator gives the effective length, the slenderness ratio RB, the beam stability factor CL, the reduced bending value and the moment capacity.

Example

A 2×10 joist (1.5 in × 9.25 in) has its compression edge braced every 96 in, with Fb* = 1,150 psi and E’min = 580,000 psi. Since 96 / 9.25 = 10.4 is more than 7, the effective length is 1.84 × 96 = 176.6 in. The slenderness is RB = √(Le d / b²) = 26.9, which is below the limit of 50. The critical value is FbE = 1.20 × 580,000 / RB² = 958 psi. The stability factor is CL = 0.733, so Fb’ = 843 psi and the moment capacity is 1.50 kip·ft.

Why it matters

The calculator helps carpenters, designers and students to see how much strength a deep joist or beam loses when the compression edge has no lateral support, and to choose the spacing of the blocking or the bridging.

Good to know

Use the unbraced length of the compression edge, which is the top edge for a simple span. A subfloor or roof sheathing nailed to the edge gives a full bracing and CL = 1.0. For a cantilever or a beam with a load at the compression edge, take the effective length from the NDS table. Check the bearing and the shear separately.

The wood beam span calculator sizes a joist for the span, the wood column capacity calculator checks the column stability factor, the glulam calculator gives the volume factor and the joist notch calculator checks the allowed notches and holes.

Frequently asked questions

What is the beam stability factor CL?

CL is the factor of the NDS that reduces the bending design value of a deep, narrow beam whose compression edge is not braced. The compression edge of a beam wants to buckle sideways like a column. A deep, narrow member, like a 2×12, loses much more strength than a square one. CL is 1.0 when the compression edge is fully braced, such as a joist with sheathing nailed on it.

How is the effective length found?

The NDS gives the effective length Le from the unbraced length lu and the loading. For a single-span beam with a uniform load, Le = 1.63 lu + 3 d if lu / d is below 7, and Le = 1.84 lu if lu / d is 7 or more. For a concentrated load at the middle, the values are different. The calculator uses the uniform load case. Use the table 3.3.3 of the NDS for the other cases.

What is the limit of RB?

The slenderness ratio RB = √(Le d / b²) must not exceed 50. Above 50, the beam is too slender and must be braced. Most sawn lumber beams have an RB between 10 and 30. A low RB gives a CL near 1.0, and a high RB gives a small CL because the critical stress FbE falls with RB squared.

What does the calculator leave out?

The calculator uses the equations of the NDS 3.3.3 for rectangular sawn lumber and glued laminated timber with a constant section. It leaves out the other adjustment factors (load duration, wet service, temperature, size, flat use), the volume factor of glulam, the shear and the bearing. Apply CL together with the volume factor only through the smaller of the two, as the NDS says.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.