Skip to content
Omnikalc

Vibrating screen efficiency and mass balance calculator

Enter the feed rate and the percent of undersize in the feed, the overflow and the underflow to get the underflow and overflow tonnage, the recoveries and the overall efficiency of the screen.

Updated on
Your inputs
tph

Value out of range

%

Value out of range

%

Value out of range

%

Value out of range

Results

Overall screening efficiency

90.9 %

Efficient screening
Underflow (through the deck)
84.8 tph
Overflow (oversize product)
115.2 tph
Recovery of undersize to the underflow
92.3 %
Recovery of oversize to the overflow
98.5 %

The vibrating screen efficiency calculator solves the mass balance of a screen deck from the undersize in the feed, the overflow and the underflow, and gives the tonnage of each product, the recovery of undersize and the overall screening efficiency.

How the calculation works

  • Enter the feed rate and the percent of undersize (material finer than the deck opening) in the feed, in the overflow and in the underflow, from sieve tests.
  • The calculator solves the mass balance of the screen for the tons of underflow and overflow.
  • It gives the recovery of undersize, the recovery of oversize and the overall screening efficiency.

Example

A screen takes 200 tph with 45 % undersize. The overflow has 6 % undersize left and the underflow has 98 % undersize. The underflow is 200 × (45 − 6) / (98 − 6) = 84.8 tph and the overflow 115.2 tph. The recovery of undersize is 84.8 × 0.98 / (200 × 0.45) = 92.3 % and the recovery of oversize is 98.5 %. The overall efficiency is the product, 90.9 %.

Why it matters

The calculator helps plant operators, quarry and aggregate engineers, process engineers and students to evaluate how well a screen separates, to find where the loss is and to compare decks, feed rates and settings.

Good to know

Sample the three streams at the same time, with a cross-stream cutter, and screen them in the laboratory on a sieve of the deck opening. Use the percent finer than the opening, not the percent passing a nominal size, and make the balance of the weights close. If the underflow is predicted at more than the feed, a sample is wrong. Use the results to compare conditions, one change at a time, such as the feed rate or the deck opening. An efficiency over 100 % or a negative flow shows an error in the data.

The cyclone cut size calculator gives the cut of a hydrocyclone, the belt conveyor calculator gives the capacity of a belt, the Bond comminution energy calculator gives the energy to crush and the ball mill calculator gives the critical speed.

Frequently asked questions

What is the undersize?

The undersize of a screen deck is the material finer than the opening of the deck, which should pass through. The oversize is the material coarser than the opening, which should stay on top and leave at the discharge end. In practice some undersize stays in the oversize and some oversize passes through the worn or large openings, so the products are not perfect.

How does the mass balance work?

The feed is the sum of the underflow and the overflow, and the undersize in the feed is the sum of the undersize in the two products. Writing the two balances gives the underflow as the feed times the difference between the undersize in the feed and in the overflow, divided by the difference between the undersize in the underflow and in the overflow.

What is a good efficiency?

A well-run screen reaches 90 % or more of overall efficiency, and a screen on a dry, free-flowing material with a good deck does better. Overloading, wet or clayey feed, blinding or pegging of the openings, worn decks and a bad stroke or slope reduce it. A fall of the recovery of undersize shows that fines are lost to the overflow.

What does the calculator leave out?

The calculator leaves out the capacity and the size of the screen, the near size particles, the deck angle and the stroke, and the cut size. It uses the analysis of the three streams, so sample all of them at the same time and with care, since an error of a few percent in a stream changes the efficiency a great deal.

Was this calculator helpful?

Thanks for your feedback!

Results are estimates provided for information purposes. They do not replace professional advice.